Lite On writer gone slower using clone - Club CDFreaks

TIMMY4 · 29-01-2003

Recently wiped my computer and reloaded software.

However since doing this everything using clone cd has gone slower.

It takes 20 mins to write a vcd at 12 speed (used to take around 7 mins) and takes 15 mins to write a pc game at 8 speed (used to also be around 7 mins).

Tried different media - Verbatim, Traxdata & Nugen.

System spec as follows;
P4, 1.4 processor windows ME operating system
256 ddr memory
lite-on 40125s writer, firmware ZS0P
Clone version 4.2.0.2

When I use nero disk times were as they were before.

Clone was quicker before I wiped hard drive though I did use previous version of clone cd.

My mate though has got a P3, 1.0 processor with windows ME, SAME WRITER, SAME CLONE VERSION and his can write the speeds I used to get.

Any suggestions?

*shuss* · 30-01-2003

have u remembersed to enable dma for the Hard drive[s] and optical drives
?

nouturn20 · 30-01-2003

Do you have DMA enabled? In 2k/XP DMA isn't enabled out of the box which means you must enable it. to enable it go to the device magager, select IDE ATA/ATAPI controller, right click on primary IDE channel, properties, advanced settings, and make sure it the drop down boxs say DMA if available. Repeat process for secondary IDE channel.

TIMMY4 · 30-01-2003

Went into settings and there was no tick in DMA settings for writer or dvd rom so put ticks in all applicable drives and then re-booted.

However problem still not solved.

Did same vcd disk and again same problem - disk written at 12 speed took 20 minutes.

*shuss* · 30-01-2003

enable dma for ur hard drive too

TIMMY4 · 31-01-2003

Thanks for help so far but just tried that and still no luck - still takes along time burning disks.

My mate said it could be to do with the ide cables and how they are connected to writer / hard drive.

What is the best way to have them?

29-01-2003	#1 (permalink)
TIMMY4 New on Forum Join Date: May 2002 Posts: 24	Lite On writer gone slower using clone <a href='http://adstats.cdfreaks.com/www/delivery/ck.php?n=a13febf7&cb=INSERT_RANDOM_NUMBER_HERE' target='_blank'><img src='http://adstats.cdfreaks.com/www/delivery/avw.php?zoneid=30&cb=INSERT_RANDOM_NUMBER_HERE&n=a13febf7' border='0' alt='' /></a> Recently wiped my computer and reloaded software. However since doing this everything using clone cd has gone slower. It takes 20 mins to write a vcd at 12 speed (used to take around 7 mins) and takes 15 mins to write a pc game at 8 speed (used to also be around 7 mins). Tried different media - Verbatim, Traxdata & Nugen. System spec as follows; P4, 1.4 processor windows ME operating system 256 ddr memory lite-on 40125s writer, firmware ZS0P Clone version 4.2.0.2 When I use nero disk times were as they were before. Clone was quicker before I wiped hard drive though I did use previous version of clone cd. My mate though has got a P3, 1.0 processor with windows ME, SAME WRITER, SAME CLONE VERSION and his can write the speeds I used to get. Any suggestions?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
clone dvd burning slower	ochacon	CloneDVD	11	22-10-2006 02:57
Lite-On SHW 160P6S, slower than my Toshiba 2x?!	morgan2	Newbie Forum	11	06-10-2006 21:38
problems using 8X or 16X media in slower writer??	achookang	Newbie Forum	8	28-08-2005 10:16
My Lite-On is slower than my NEC! Need Ideas	amdcrazy	General Hardware Forum	1	09-12-2004 04:58
lite-on 32x burns slower than 16x	Xidus	LiteOn / PLDS/ Sony Burner	6	27-05-2002 00:50

Commercial message
<a href='http://adstats.cdfreaks.com/www/delivery/ck.php?n=ac816a32&cb=INSERT_RANDOM_NUMBER_HERE' target='_blank'><img src='http://adstats.cdfreaks.com/www/delivery/avw.php?zoneid=29&cb=INSERT_RANDOM_NUMBER_HERE&n=ac816a32' border='0' alt='' /></a>

30-01-2003	#2 (permalink)
shuss CDFreaks Resident Join Date: Feb 2002 Location: UK Posts: 1,425	have u remembersed to enable dma for the Hard drive[s] and optical drives ?

30-01-2003	#3 (permalink)
nouturn20 CD Freaks Junior Member Join Date: Jul 2002 Posts: 53	Do you have DMA enabled? In 2k/XP DMA isn't enabled out of the box which means you must enable it. to enable it go to the device magager, select IDE ATA/ATAPI controller, right click on primary IDE channel, properties, advanced settings, and make sure it the drop down boxs say DMA if available. Repeat process for secondary IDE channel.

30-01-2003	#4 (permalink)
TIMMY4 New on Forum Join Date: May 2002 Posts: 24	Went into settings and there was no tick in DMA settings for writer or dvd rom so put ticks in all applicable drives and then re-booted. However problem still not solved. Did same vcd disk and again same problem - disk written at 12 speed took 20 minutes.

30-01-2003	#5 (permalink)
shuss CDFreaks Resident Join Date: Feb 2002 Location: UK Posts: 1,425	enable dma for ur hard drive too

31-01-2003	#6 (permalink)
TIMMY4 New on Forum Join Date: May 2002 Posts: 24	Thanks for help so far but just tried that and still no luck - still takes along time burning disks. My mate said it could be to do with the ide cables and how they are connected to writer / hard drive. What is the best way to have them?