Trouble backing up Eargon - Club CDFreaks

Bushwacker6566 · 27-03-2007

Is anyone having trouble backing up this movie. Say's it completed but it didn't burn; along with Rocky Balboa, Garfield, and Curious George.

astone2665 · 27-03-2007

Hello Bushwacker6566 and welcome to the forum. You will have to give us a little more information concerning your issue. I myself didn't have any problem backing up either Eargon or Rocky Balboa, or for that matter Garfield. What version of Fab are you using? Have you tried opening the DVD after it's done to see if the files are there? Are you using Gold/Plat. to make the back up or DVDFab Decrypter and another burn engine? Has the same thing happened with each attempt with all of these movie's? They are Sony movie's I believe, and are more complicated with there encryption. Rocky took me a little longer to read. What are your settings? Go to common settings and open it. Click on Read on the left hand side. At the top is I/O Mode, set to SPTI. Then click on Write on the left hand side and make sure it's set to VSO Burning Engine. Then go down to Write Speed and set it to 1/2 of the rated speed of the media you are using, usally 4x or 8x is best till you figure out what's happening. Then go to Write Speed and set it to SAO Writing. Next, DVD Size, I use 4472. Just click the drop down box and you'll see it there. And last but not least, check the box for Set Booktype to DVD-Rom if you are using +R media or +RW. These are the settings I use to make perfect back ups. Now if you aren't using Platinum or Gold these settings won't do you any good. Hope this helps and let us know how you make out. ~ Mike

Bushwacker6566 · 27-03-2007

Hi astone,
Thanks for the reply.

Ok let me see here. I'm using purchase version of DVDFab Gold ver 3.0.8.6
I have opened the DVD that was supposed to be written to and there are no files on disk.
Yes the it's the same thing for all these movies.
My settings were different than what you have posted. I just changed them and now I'm trying again with eragon.
The media type is TDK DVD -R 1-16x 4.7GB

Just to make sure, I burned a movie that I new I could and I was able to, just in case my burner had gone out.

astone2665 · 27-03-2007

Hi Bushwacker, you may want to download the newest version of Fab, ver. 3.0.9.0. Version 8.6. had a few problems with it, but the new ver. seems to have corrected most of them. ~ Mike

Bushwacker6566 · 27-03-2007

Sorry, but I don't see 3.0.9.0. The URL I'm going to is www.dvdfab.com then the download link for the history. Could you provide me with a link to where you get the 9.0 please.

brwiggins · 27-03-2007

I was having a similar problem as well with some movies. Try downloading ISOBuster and see if you can see the files on the disc (you can use the free functionality to do this)

*bigmacnc* · 27-03-2007

Try here:

http://club.cdfreaks.com/showthread.php?t=213110

Mack

Bushwacker6566 · 27-03-2007

Thank you all for the information. Sorry I'm such a nOOb to this. Umm what is ISOBuster anyway, is it a stand alone program? One last thing, do you think it would be better for me to switch to DVDFab Platinum. One thing I would really like to do besides copy dvd's to another dvd is copy it to my hdd and watch it from there as well. Oh and do you think I should start buying better media, such as maybe Verbatim disks or something?

*maineman* · 27-03-2007

Hi Bushwacker6566,

The latest Beta versions are always posted here on cdf in the Fab forum.
Look at or near the top, amongst the stickies, ^Mack's link above^.
Final release versions are always posted on Fengtao's home site:
http://www.dvdfab.com/download.htm

Platinum is very feature rich as opposed to Gold and you never know when you'll want some of those features. 3-4 months ago, I never thought I'd be doing Ipod conversions. For $19.95 it's well worth the upgrade price. Still, Gold should put out the same quality rip and burn.

Ripping to your hdd can be done with platinum, gold or even dvdfab decrypter (freeware). Simply choose any desired location on your hdd (remember the file path so you can find it) as the "target" instead of your burner. It's as easy as that. You will need a software player such as powerdvd, nero showtime, WMP, Windvd, etc. IMO, the best one out there is VLC...will play darn near anything and it's free...just click on the link in my sig.

For SL discs, go with verbatim or Taiyo Yuden.

brwiggins · 28-03-2007

Quote:

Originally Posted by Bushwacker6566

Thank you all for the information. Sorry I'm such a nOOb to this. Umm what is ISOBuster anyway, is it a stand alone program? One last thing, do you think it would be better for me to switch to DVDFab Platinum. One thing I would really like to do besides copy dvd's to another dvd is copy it to my hdd and watch it from there as well. Oh and do you think I should start buying better media, such as maybe Verbatim disks or something?

ISO Buster is a completely separate app from fab. You can download it here -->http://www.isobuster.com/isobusterdownload.php

For what you are doing, gold or platinum should work. I have platinum and have had this issue a couple of times. TDK media is ranked just as high as verbatim according to this site

http://www.digitalfaq.com/media/dvdmedia.htm

Bushwacker6566 · 28-03-2007

Ok well I installed the 3.0.9.0 Beta version and I'm still not able to backup any of the disks. DANG IT. When I try to do the whole disk I get this error.

No media inserted.
Please insert a compatible media to start the write process.

Man I just don't get it. I'm going to see if I can upload some pics for you guy's so you can see some key points on previous trys.

StormJumper · 28-03-2007

Quote:

Originally Posted by Bushwacker6566

Ok well I installed the 3.0.9.0 Beta version and I'm still not able to backup any of the disks. DANG IT. When I try to do the whole disk I get this error.

No media inserted.
Please insert a compatible media to start the write process.

Man I just don't get it. I'm going to see if I can upload some pics for you guy's so you can see some key points on previous trys.

Hi Bushwacker
According to the last picture you posted it Completed sucessfully

BTW I see you use WindowBlinds

great program I also use it have made a few skins myself

*maineman* · 28-03-2007

Yeah, I'm not sure I follow either. Let's see if we have this right...
On full disc, you get the error:

No media inserted.
Please insert a compatible media to start the write process.

On main movie, the process seems to complete successfully, but the disc is blank?. Is this right?
Are you still able to use the blank disc? is it really completely blank or just appear that way?

Try main movie again, but do this first.
"Common settings" > "General" >
Unclick "Delete temporary files when finished"
Remember the location of your temporary directory so you can find the files later on (just follow the file path).
(You can actually place this directory anywhere you want on the hdd, just as you can choose any target location on the hdd instead of your burner, but do whatever is easy for you).

Now, before you try to do another bkup, make sure your temp directory is empty...just delete anything in there.
How much free space do you have on your hdd?

Ok, try Main movie again. Let's assume your "bkup" is blank.
Go to the temp directory...the files should still be there, even though the process completed successfully and you clicked on "Finished".
You should be able to view the movie off your hdd.

Let us know what happens...

Jimbo · 28-03-2007

Just a thought here, maybe your burner doesn't like TDK blank media, I know it might sound silly but my burners just don't like Sony disk, have problems with them and I thought Sony was a good brand, so I switched to Verbs' and no problems since

*maineman* · 28-03-2007

Quote:

Originally Posted by Jimbo

Just a thought here, maybe your burner doesn't like TDK blank media, I know it might sound silly but my burners just don't like Sony disk, have problems with them and I thought Sony was a good brand, so I switched to Verbs' and no problems since

Yeah Jimbo, I agree. I recommended verbs and TY's to the OP also for the same reason you describe.
This is no disrespect to brwiggins or TDK. He's absolutely correct about the quality of TDK, but I think the TDKs...like the Sonys tend to be more finicky when it comes to overall compatibilty.

You never know for sure what's gonna work. I know one of the mods who can't get TY media to burn correctly in a particular burner. He finally gave up trying to figure it out...

Changing the media is definitely worth a try...

brwiggins · 28-03-2007

Quote:

Originally Posted by maineman

This is no disrespect to brwiggins or TDK. He's absolutely correct about the quality of TDK, but I think the TDKs...like the Sonys tend to be more finicky when it comes to overall compatibilty.

No disrespect at all..I am by no means a media expert....switching media is an excellent idea. I used to have problems with Sony and went to TDK because I had better luck. When I run out of these I plan on buying some TY to see how they work.

You just have to do a bit of trial and error to see which media works best with your burner.

Bushwacker6566 · 28-03-2007

I was able to copy it to my DVDFab folder as shown in pic below. Now I just need to figure out how to get it to disk and to view it on my pc lol. I too agree with those who were talking about disk's and my burner, only Ive backed up to these TDK disks already. So it kinda makes me wonder. I just tried to burn the files from my HDD as the source to a blank in the burner and got the

No media inserted.
Please insert a compatible media to start the write process.

signals · 28-03-2007

Quote:

Originally Posted by Bushwacker6566

I was able to copy it to my DVDFab folder as shown in pic below. Now I just need to figure out how to get it to disk and to view it on my pc lol. I too agree with those who were talking about disk's and my burner, only Ive backed up to these TDK disks already. So it kinda makes me wonder. I just tried to burn the files from my HDD as the source to a blank in the burner and got the

No media inserted.
Please insert a compatible media to start the write process.

Suggestions: See if you can see the temp files in the VIDEO_TS folder. If they are there (filetypes IFO, BUP and VOB), try the Write Data mode to burn the temp files to disc. If that does not work, post the burn log entries from one of these failed attempts. It may contain an error code or other information that will help. The logfile can be found at: C:\Documents and Settings\..username...\My Documents\DVDFab\Log in a text file named dvdfab_burn_vso.log. Just open the file with notepad and copy entries from the past 1 or 2 failed attempts and paste them into a post so we can take a look.
/EDIT/ There is a firmware update available for your drive. You also might want to read this thread: http://club.cdfreaks.com/showpost.ph...6&postcount=11 to make sure you have the correct cable.

*bigmacnc* · 28-03-2007

Does the burned disc show the burn lines and what does windows explorer report that is on the disc?

Mack

t0nee1 · 29-03-2007

Bushwacker wrote "I was able to copy it to my DVDFab folder." if successful, then
just use IMGBurn on VIDEO_TS folder to build an ISO....and burn... with diff. media....
preferably Verbs.....

Bushwacker6566 · 29-03-2007

Sorry forgot to upload the files img from previous post. As you can see they did get to my HDD. And for the other suggestions I will try now.

signals · 29-03-2007

Quote:

Originally Posted by Bushwacker6566

Sorry forgot to upload the files img from previous post. As you can see they did get to my HDD. And for the other suggestions I will try now.

You're halfway there at least!

If it doesn't work again, the burn logs would sure be a big help.

Bushwacker6566 · 29-03-2007

Log File.

3/28/2007 12:38:27 PM info ******************** Report session closed *********************
3/28/2007 12:38:12 PM info Compatible media types : DVD-R, DVD-RW Seq., DVD-RW RO, DVD+R, DVD+RW, CD-R, CD-RW, DL DVD+R, DL DVD-R
3/28/2007 12:38:12 PM info New Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/28/2007 12:36:13 PM info Current Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/28/2007 12:36:13 PM info Using Patin-Couffin driver Version 1.37, Internal revision 37 - Async. Access mode
3/28/2007 12:36:13 PM info User default language : 1033 (0x0409h) - English (United States)
3/28/2007 12:36:13 PM info System default language : 1033 (0x0409h) - English (United States)
3/28/2007 12:36:13 PM info DLL Version 2.0.25.278
3/28/2007 12:36:13 PM info DLL C:\Program Files\DVDFab Gold 3\vso_hwe.dll
3/28/2007 12:36:13 PM info Version 3, 0, 9, 0
3/28/2007 12:36:13 PM info ExeName : "C:\Program Files\DVDFab Gold 3\DVDFabGold.exe"
3/28/2007 12:36:13 PM info OS : Microsoft Windows XP Professional Service Pack 2 (Build 2600)
3/28/2007 12:36:13 PM info ******************** Report session started ********************

3/28/2007 12:38:12 PM info Compatible media types : DVD-R, DVD-RW Seq., DVD-RW RO, DVD+R, DVD+RW, CD-R, CD-RW, DL DVD+R, DL DVD-R
3/28/2007 12:38:12 PM info New Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/28/2007 12:36:13 PM info Current Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/28/2007 12:36:13 PM info Using Patin-Couffin driver Version 1.37, Internal revision 37 - Async. Access mode
3/28/2007 12:36:13 PM info User default language : 1033 (0x0409h) - English (United States)
3/28/2007 12:36:13 PM info System default language : 1033 (0x0409h) - English (United States)
3/28/2007 12:36:13 PM info DLL Version 2.0.25.278
3/28/2007 12:36:13 PM info DLL C:\Program Files\DVDFab Gold 3\vso_hwe.dll
3/28/2007 12:36:13 PM info Version 3, 0, 9, 0
3/28/2007 12:36:13 PM info ExeName : "C:\Program Files\DVDFab Gold 3\DVDFabGold.exe"
3/28/2007 12:36:13 PM info OS : Microsoft Windows XP Professional Service Pack 2 (Build 2600)
3/28/2007 12:36:13 PM info ******************** Report session started ********************

3/28/2007 12:32:25 PM info ******************** Report session closed *********************
3/28/2007 12:31:44 PM info Current Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/28/2007 12:31:44 PM info Using Patin-Couffin driver Version 1.37, Internal revision 37 - Async. Access mode
3/28/2007 12:31:44 PM info User default language : 1033 (0x0409h) - English (United States)
3/28/2007 12:31:44 PM info System default language : 1033 (0x0409h) - English (United States)
3/28/2007 12:31:44 PM info DLL Version 2.0.25.278
3/28/2007 12:31:44 PM info DLL C:\Program Files\DVDFab Gold 3\vso_hwe.dll
3/28/2007 12:31:44 PM info Version 3, 0, 9, 0
3/28/2007 12:31:44 PM info ExeName : "C:\Program Files\DVDFab Gold 3\DVDFabGold.exe"
3/28/2007 12:31:44 PM info OS : Microsoft Windows XP Professional Service Pack 2 (Build 2600)
3/28/2007 12:31:44 PM info ******************** Report session started ********************

3/28/2007 12:31:44 PM info Current Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/28/2007 12:31:44 PM info Using Patin-Couffin driver Version 1.37, Internal revision 37 - Async. Access mode
3/28/2007 12:31:44 PM info User default language : 1033 (0x0409h) - English (United States)
3/28/2007 12:31:44 PM info System default language : 1033 (0x0409h) - English (United States)
3/28/2007 12:31:44 PM info DLL Version 2.0.25.278
3/28/2007 12:31:44 PM info DLL C:\Program Files\DVDFab Gold 3\vso_hwe.dll
3/28/2007 12:31:44 PM info Version 3, 0, 9, 0
3/28/2007 12:31:44 PM info ExeName : "C:\Program Files\DVDFab Gold 3\DVDFabGold.exe"
3/28/2007 12:31:44 PM info OS : Microsoft Windows XP Professional Service Pack 2 (Build 2600)
3/28/2007 12:31:44 PM info ******************** Report session started ********************

3/28/2007 11:24:57 AM info ******************** Report session closed *********************
3/28/2007 10:35:56 AM info Compatible media types : DVD-R, DVD-RW Seq., DVD-RW RO, DVD+R, DVD+RW, CD-R, CD-RW, DL DVD+R, DL DVD-R
3/28/2007 10:35:56 AM info New Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/28/2007 10:34:29 AM info Current Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/28/2007 10:34:29 AM info Using Patin-Couffin driver Version 1.37, Internal revision 37 - Async. Access mode
3/28/2007 10:34:29 AM info User default language : 1033 (0x0409h) - English (United States)
3/28/2007 10:34:29 AM info System default language : 1033 (0x0409h) - English (United States)
3/28/2007 10:34:29 AM info DLL Version 2.0.25.278
3/28/2007 10:34:29 AM info DLL C:\Program Files\DVDFab Gold 3\vso_hwe.dll
3/28/2007 10:34:29 AM info Version 3, 0, 9, 0
3/28/2007 10:34:29 AM info ExeName : "C:\Program Files\DVDFab Gold 3\DVDFabGold.exe"
3/28/2007 10:34:29 AM info OS : Microsoft Windows XP Professional Service Pack 2 (Build 2600)
3/28/2007 10:34:29 AM info ******************** Report session started ********************

3/28/2007 10:35:56 AM info Compatible media types : DVD-R, DVD-RW Seq., DVD-RW RO, DVD+R, DVD+RW, CD-R, CD-RW, DL DVD+R, DL DVD-R
3/28/2007 10:35:56 AM info New Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/28/2007 10:34:29 AM info Current Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/28/2007 10:34:29 AM info Using Patin-Couffin driver Version 1.37, Internal revision 37 - Async. Access mode
3/28/2007 10:34:29 AM info User default language : 1033 (0x0409h) - English (United States)
3/28/2007 10:34:29 AM info System default language : 1033 (0x0409h) - English (United States)
3/28/2007 10:34:29 AM info DLL Version 2.0.25.278
3/28/2007 10:34:29 AM info DLL C:\Program Files\DVDFab Gold 3\vso_hwe.dll
3/28/2007 10:34:29 AM info Version 3, 0, 9, 0
3/28/2007 10:34:29 AM info ExeName : "C:\Program Files\DVDFab Gold 3\DVDFabGold.exe"
3/28/2007 10:34:29 AM info OS : Microsoft Windows XP Professional Service Pack 2 (Build 2600)
3/28/2007 10:34:29 AM info ******************** Report session started ********************

3/27/2007 10:41:04 PM info ******************** Report session closed *********************
3/27/2007 10:40:00 PM info Media removed. Burning layer not ready to write
3/27/2007 10:39:58 PM info Finalization Time 00:00:21 - Total completion time 00:15:26
3/27/2007 10:39:36 PM info Write finished in 00:15:05 - Finalization start here. Avg. burn rate 4.10
3/27/2007 10:24:36 PM info Lead-in burning time (mS) 5000
3/27/2007 10:24:31 PM info Write started 2285520 sectors to write
3/27/2007 10:24:31 PM info Init success: DVD-R SAO
3/27/2007 10:24:31 PM info Writing speed requested x4.0, effective x4.0
3/27/2007 10:24:30 PM info Available write speed: 16x, 12x, 8x, 6x, 4x
3/27/2007 10:24:30 PM info Media ID: CMC MAG. AM3
3/27/2007 10:24:30 PM info DMA Enabled
3/27/2007 10:24:30 PM info Scanned files #9, folder #2 - total size 4679649280 b. (4.36 Gb.)
3/27/2007 10:24:30 PM info Inserted media type : DVD-R
3/27/2007 10:24:30 PM info Write started
3/27/2007 10:09:40 PM info New media inserted. Burning layer is ready to write
3/27/2007 10:09:40 PM info Compatible media types : DVD-R, DVD-RW Seq., DVD-RW RO, DVD+R, DVD+RW, CD-R, CD-RW, DL DVD+R, DL DVD-R
3/27/2007 10:09:40 PM info New Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/27/2007 10:08:29 PM info New media inserted. Burning layer is ready to write
3/27/2007 10:08:26 PM info Current Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/27/2007 10:08:26 PM info Using Patin-Couffin driver Version 1.37, Internal revision 37 - Async. Access mode
3/27/2007 10:08:26 PM info User default language : 1033 (0x0409h) - English (United States)
3/27/2007 10:08:26 PM info System default language : 1033 (0x0409h) - English (United States)
3/27/2007 10:08:26 PM info DLL Version 2.0.25.278
3/27/2007 10:08:26 PM info DLL C:\Program Files\DVDFab Gold 3\vso_hwe.dll
3/27/2007 10:08:26 PM info Version 3, 0, 9, 0
3/27/2007 10:08:26 PM info ExeName : "C:\Program Files\DVDFab Gold 3\DVDFabGold.exe"
3/27/2007 10:08:26 PM info OS : Microsoft Windows XP Professional Service Pack 2 (Build 2600)
3/27/2007 10:08:26 PM info ******************** Report session started ********************

3/27/2007 10:40:00 PM info Media removed. Burning layer not ready to write
3/27/2007 10:39:58 PM info Finalization Time 00:00:21 - Total completion time 00:15:26
3/27/2007 10:39:36 PM info Write finished in 00:15:05 - Finalization start here. Avg. burn rate 4.10
3/27/2007 10:24:36 PM info Lead-in burning time (mS) 5000
3/27/2007 10:24:31 PM info Write started 2285520 sectors to write
3/27/2007 10:24:31 PM info Init success: DVD-R SAO
3/27/2007 10:24:31 PM info Writing speed requested x4.0, effective x4.0
3/27/2007 10:24:30 PM info Available write speed: 16x, 12x, 8x, 6x, 4x
3/27/2007 10:24:30 PM info Media ID: CMC MAG. AM3
3/27/2007 10:24:30 PM info DMA Enabled
3/27/2007 10:24:30 PM info Scanned files #9, folder #2 - total size 4679649280 b. (4.36 Gb.)
3/27/2007 10:24:30 PM info Inserted media type : DVD-R
3/27/2007 10:24:30 PM info Write started
3/27/2007 10:09:40 PM info New media inserted. Burning layer is ready to write
3/27/2007 10:09:40 PM info Compatible media types : DVD-R, DVD-RW Seq., DVD-RW RO, DVD+R, DVD+RW, CD-R, CD-RW, DL DVD+R, DL DVD-R
3/27/2007 10:09:40 PM info New Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/27/2007 10:08:29 PM info New media inserted. Burning layer is ready to write
3/27/2007 10:08:26 PM info Current Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/27/2007 10:08:26 PM info Using Patin-Couffin driver Version 1.37, Internal revision 37 - Async. Access mode
3/27/2007 10:08:26 PM info User default language : 1033 (0x0409h) - English (United States)
3/27/2007 10:08:26 PM info System default language : 1033 (0x0409h) - English (United States)
3/27/2007 10:08:26 PM info DLL Version 2.0.25.278
3/27/2007 10:08:26 PM info DLL C:\Program Files\DVDFab Gold 3\vso_hwe.dll
3/27/2007 10:08:26 PM info Version 3, 0, 9, 0
3/27/2007 10:08:26 PM info ExeName : "C:\Program Files\DVDFab Gold 3\DVDFabGold.exe"
3/27/2007 10:08:26 PM info OS : Microsoft Windows XP Professional Service Pack 2 (Build 2600)
3/27/2007 10:08:26 PM info ******************** Report session started ********************

3/27/2007 10:08:16 PM info ******************** Report session closed *********************
3/27/2007 9:56:14 PM info Compatible media types : DVD-R, DVD-RW Seq., DVD-RW RO, DVD+R, DVD+RW, CD-R, CD-RW, DL DVD+R, DL DVD-R
3/27/2007 9:56:14 PM info New Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/27/2007 9:54:07 PM info Current Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/27/2007 9:54:07 PM info Using Patin-Couffin driver Version 1.37, Internal revision 37 - Async. Access mode
3/27/2007 9:54:07 PM info User default language : 1033 (0x0409h) - English (United States)
3/27/2007 9:54:07 PM info System default language : 1033 (0x0409h) - English (United States)
3/27/2007 9:54:07 PM info DLL Version 2.0.25.278
3/27/2007 9:54:07 PM info DLL C:\Program Files\DVDFab Gold 3\vso_hwe.dll
3/27/2007 9:54:07 PM info Version 3, 0, 9, 0
3/27/2007 9:54:07 PM info ExeName : "C:\Program Files\DVDFab Gold 3\DVDFabGold.exe"
3/27/2007 9:54:07 PM info OS : Microsoft Windows XP Professional Service Pack 2 (Build 2600)
3/27/2007 9:54:07 PM info ******************** Report session started ********************

3/27/2007 9:56:14 PM info Compatible media types : DVD-R, DVD-RW Seq., DVD-RW RO, DVD+R, DVD+RW, CD-R, CD-RW, DL DVD+R, DL DVD-R
3/27/2007 9:56:14 PM info New Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/27/2007 9:54:07 PM info Current Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/27/2007 9:54:07 PM info Using Patin-Couffin driver Version 1.37, Internal revision 37 - Async. Access mode
3/27/2007 9:54:07 PM info User default language : 1033 (0x0409h) - English (United States)
3/27/2007 9:54:07 PM info System default language : 1033 (0x0409h) - English (United States)
3/27/2007 9:54:07 PM info DLL Version 2.0.25.278
3/27/2007 9:54:07 PM info DLL C:\Program Files\DVDFab Gold 3\vso_hwe.dll
3/27/2007 9:54:07 PM info Version 3, 0, 9, 0
3/27/2007 9:54:07 PM info ExeName : "C:\Program Files\DVDFab Gold 3\DVDFabGold.exe"
3/27/2007 9:54:07 PM info OS : Microsoft Windows XP Professional Service Pack 2 (Build 2600)
3/27/2007 9:54:07 PM info ******************** Report session started ********************

3/27/2007 6:32:29 PM info ******************** Report session closed *********************
3/27/2007 6:32:22 PM info Current Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/27/2007 6:32:22 PM info Using Patin-Couffin driver Version 1.37, Internal revision 37 - Async. Access mode
3/27/2007 6:32:22 PM info User default language : 1033 (0x0409h) - English (United States)
3/27/2007 6:32:22 PM info System default language : 1033 (0x0409h) - English (United States)
3/27/2007 6:32:22 PM info DLL Version 2.0.25.278
3/27/2007 6:32:22 PM info DLL C:\Program Files\DVDFab Gold 3\vso_hwe.dll
3/27/2007 6:32:22 PM info Version 3, 0, 8, 6
3/27/2007 6:32:22 PM info ExeName : "C:\Program Files\DVDFab Gold 3\DVDFabGold.exe"
3/27/2007 6:32:22 PM info OS : Microsoft Windows XP Professional Service Pack 2 (Build 2600)
3/27/2007 6:32:22 PM info ******************** Report session started ********************

3/27/2007 6:32:22 PM info Current Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/27/2007 6:32:22 PM info Using Patin-Couffin driver Version 1.37, Internal revision 37 - Async. Access mode
3/27/2007 6:32:22 PM info User default language : 1033 (0x0409h) - English (United States)
3/27/2007 6:32:22 PM info System default language : 1033 (0x0409h) - English (United States)
3/27/2007 6:32:22 PM info DLL Version 2.0.25.278
3/27/2007 6:32:22 PM info DLL C:\Program Files\DVDFab Gold 3\vso_hwe.dll
3/27/2007 6:32:22 PM info Version 3, 0, 8, 6
3/27/2007 6:32:22 PM info ExeName : "C:\Program Files\DVDFab Gold 3\DVDFabGold.exe"
3/27/2007 6:32:22 PM info OS : Microsoft Windows XP Professional Service Pack 2 (Build 2600)
3/27/2007 6:32:22 PM info ******************** Report session started ********************

Jimbo · 29-03-2007

Don't know whats going on here myself but the latest FW for that burner is 1.09

signals · 29-03-2007

Good job.

The drive is failing to communicate with the burning engine. In Common Settings-->Read, see what setting is selected for I/O mode, near the top. If it is still set to auto, try setting it to SPTI using the drop down selector. Tell me what is happening when the file says "Report Session Closed". Has it given you a completion message at this point? Crashed? Disc ejected? The burning engine has given up without reporting an error for some reason. This is just about 2 minutes after the session was opened. If you have Nero on your machine, you can try burning with that instead of VSO and see if it makes any difference. This is selected in Common Settings-->Write using a drop down box. The firmware update for the Pioneer drive also begins to look like a good idea: your drive's version: 1.06, current version, 1.09

Quote:

Originally Posted by Bushwacker6566

Log File.

3/28/2007 12:38:27 PM info ******************** Report session closed *********************
3/28/2007 12:38:12 PM info Compatible media types : DVD-R, DVD-RW Seq., DVD-RW RO, DVD+R, DVD+RW, CD-R, CD-RW, DL DVD+R, DL DVD-R
3/28/2007 12:38:12 PM info New Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/28/2007 12:36:13 PM info Current Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/28/2007 12:36:13 PM info Using Patin-Couffin driver Version 1.37, Internal revision 37 - Async. Access mode
3/28/2007 12:36:13 PM info User default language : 1033 (0x0409h) - English (United States)
3/28/2007 12:36:13 PM info System default language : 1033 (0x0409h) - English (United States)
3/28/2007 12:36:13 PM info DLL Version 2.0.25.278
3/28/2007 12:36:13 PM info DLL C:\Program Files\DVDFab Gold 3\vso_hwe.dll
3/28/2007 12:36:13 PM info Version 3, 0, 9, 0
3/28/2007 12:36:13 PM info ExeName : "C:\Program Files\DVDFab Gold 3\DVDFabGold.exe"
3/28/2007 12:36:13 PM info OS : Microsoft Windows XP Professional Service Pack 2 (Build 2600)
3/28/2007 12:36:13 PM info ******************** Report session started ********************

3/28/2007 12:38:12 PM info Compatible media types : DVD-R, DVD-RW Seq., DVD-RW RO, DVD+R, DVD+RW, CD-R, CD-RW, DL DVD+R, DL DVD-R
3/28/2007 12:38:12 PM info New Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/28/2007 12:36:13 PM info Current Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/28/2007 12:36:13 PM info Using Patin-Couffin driver Version 1.37, Internal revision 37 - Async. Access mode
3/28/2007 12:36:13 PM info User default language : 1033 (0x0409h) - English (United States)
3/28/2007 12:36:13 PM info System default language : 1033 (0x0409h) - English (United States)
3/28/2007 12:36:13 PM info DLL Version 2.0.25.278
3/28/2007 12:36:13 PM info DLL C:\Program Files\DVDFab Gold 3\vso_hwe.dll
3/28/2007 12:36:13 PM info Version 3, 0, 9, 0
3/28/2007 12:36:13 PM info ExeName : "C:\Program Files\DVDFab Gold 3\DVDFabGold.exe"
3/28/2007 12:36:13 PM info OS : Microsoft Windows XP Professional Service Pack 2 (Build 2600)
3/28/2007 12:36:13 PM info ******************** Report session started ********************

3/28/2007 12:32:25 PM info ******************** Report session closed *********************
3/28/2007 12:31:44 PM info Current Drive selected : 2:1:0 - PIONEER DVD-RW DVR-112D 1.06 [G] (Ide)
3/28/2007 12:31:44 PM info Using Patin-Couffin driver Version 1.37, Internal revision 37 - Async. Access mode
.....edited for space********************

27-03-2007	#1 (permalink)
Bushwacker6566 New on Forum Join Date: Mar 2007 Posts: 17	Trouble backing up Eargon <a href='http://adstats.cdfreaks.com/www/delivery/ck.php?n=a13febf7&cb=INSERT_RANDOM_NUMBER_HERE' target='_blank'><img src='http://adstats.cdfreaks.com/www/delivery/avw.php?zoneid=30&cb=INSERT_RANDOM_NUMBER_HERE&n=a13febf7' border='0' alt='' /></a> Is anyone having trouble backing up this movie. Say's it completed but it didn't burn; along with Rocky Balboa, Garfield, and Curious George.

27-03-2007	#2 (permalink)
astone2665 CD Freaks Senior Member Join Date: Oct 2006 Location: Saddle, Arkansas Posts: 981	Re: Trouble backing up Eargon Hello Bushwacker6566 and welcome to the forum. You will have to give us a little more information concerning your issue. I myself didn't have any problem backing up either Eargon or Rocky Balboa, or for that matter Garfield. What version of Fab are you using? Have you tried opening the DVD after it's done to see if the files are there? Are you using Gold/Plat. to make the back up or DVDFab Decrypter and another burn engine? Has the same thing happened with each attempt with all of these movie's? They are Sony movie's I believe, and are more complicated with there encryption. Rocky took me a little longer to read. What are your settings? Go to common settings and open it. Click on Read on the left hand side. At the top is I/O Mode, set to SPTI. Then click on Write on the left hand side and make sure it's set to VSO Burning Engine. Then go down to Write Speed and set it to 1/2 of the rated speed of the media you are using, usally 4x or 8x is best till you figure out what's happening. Then go to Write Speed and set it to SAO Writing. Next, DVD Size, I use 4472. Just click the drop down box and you'll see it there. And last but not least, check the box for Set Booktype to DVD-Rom if you are using +R media or +RW. These are the settings I use to make perfect back ups. Now if you aren't using Platinum or Gold these settings won't do you any good. Hope this helps and let us know how you make out. ~ Mike

27-03-2007	#3 (permalink)
Bushwacker6566 New on Forum Join Date: Mar 2007 Posts: 17	Re: Trouble backing up Eargon Hi astone, Thanks for the reply. Ok let me see here. I'm using purchase version of DVDFab Gold ver 3.0.8.6 I have opened the DVD that was supposed to be written to and there are no files on disk. Yes the it's the same thing for all these movies. My settings were different than what you have posted. I just changed them and now I'm trying again with eragon. The media type is TDK DVD -R 1-16x 4.7GB Just to make sure, I burned a movie that I new I could and I was able to, just in case my burner had gone out.

27-03-2007	#4 (permalink)
astone2665 CD Freaks Senior Member Join Date: Oct 2006 Location: Saddle, Arkansas Posts: 981	Re: Trouble backing up Eargon Hi Bushwacker, you may want to download the newest version of Fab, ver. 3.0.9.0. Version 8.6. had a few problems with it, but the new ver. seems to have corrected most of them. ~ Mike

27-03-2007	#5 (permalink)
Bushwacker6566 New on Forum Join Date: Mar 2007 Posts: 17	Re: Trouble backing up Eargon Sorry, but I don't see 3.0.9.0. The URL I'm going to is www.dvdfab.com then the download link for the history. Could you provide me with a link to where you get the 9.0 please.

Commercial message
<a href='http://adstats.cdfreaks.com/www/delivery/ck.php?n=a5c5554b&cb=INSERT_RANDOM_NUMBER_HERE' target='_blank'><img src='http://adstats.cdfreaks.com/www/delivery/avw.php?zoneid=29&cb=INSERT_RANDOM_NUMBER_HERE&n=a5c5554b' border='0' alt='' /></a>

27-03-2007	#6 (permalink)
brwiggins CD Freaks Junior Member Join Date: Feb 2006 Posts: 87	Re: Trouble backing up Eargon I was having a similar problem as well with some movies. Try downloading ISOBuster and see if you can see the files on the disc (you can use the free functionality to do this)

27-03-2007	#7 (permalink)
bigmacnc CDFreaks Resident Join Date: Sep 2005 Posts: 1,728	Re: Trouble backing up Eargon Try here: http://club.cdfreaks.com/showthread.php?t=213110 Mack __________________ Mack Find missing DVD or CD drives download CDGONE and Disable Auto Run Click Here Media Info: Click Here To understand DMA and how to lock it click Here The more problems that I have to deal with; the more I learn Clicking on Search or Searching on Google will not cause your computer to explode That is just a rumor

27-03-2007	#8 (permalink)
Bushwacker6566 New on Forum Join Date: Mar 2007 Posts: 17	Re: Trouble backing up Eargon Thank you all for the information. Sorry I'm such a nOOb to this. Umm what is ISOBuster anyway, is it a stand alone program? One last thing, do you think it would be better for me to switch to DVDFab Platinum. One thing I would really like to do besides copy dvd's to another dvd is copy it to my hdd and watch it from there as well. Oh and do you think I should start buying better media, such as maybe Verbatim disks or something?

27-03-2007	#9 (permalink)
maineman CDFreaks Resident Join Date: Apr 2005 Location: Maine Posts: 4,245	Re: Trouble backing up Eargon Hi Bushwacker6566, The latest Beta versions are always posted here on cdf in the Fab forum. Look at or near the top, amongst the stickies, ^Mack's link above^. Final release versions are always posted on Fengtao's home site: http://www.dvdfab.com/download.htm Platinum is very feature rich as opposed to Gold and you never know when you'll want some of those features. 3-4 months ago, I never thought I'd be doing Ipod conversions. For $19.95 it's well worth the upgrade price. Still, Gold should put out the same quality rip and burn. Ripping to your hdd can be done with platinum, gold or even dvdfab decrypter (freeware). Simply choose any desired location on your hdd (remember the file path so you can find it) as the "target" instead of your burner. It's as easy as that. You will need a software player such as powerdvd, nero showtime, WMP, Windvd, etc. IMO, the best one out there is VLC...will play darn near anything and it's free...just click on the link in my sig. For SL discs, go with verbatim or Taiyo Yuden. __________________ If it ain't broke, don't fix it! How to check DMA \| More DMA Help + Reset DMA link \| Nero CD-DVD Speed \| Regseeker \| VLC Media Player You know how to whistle, don't you, Steve? You just put your lips together and... blow. \| Lauren Bacall \| "To Have and Have Not" (1944).

28-03-2007	#13 (permalink)
maineman CDFreaks Resident Join Date: Apr 2005 Location: Maine Posts: 4,245	Re: Trouble backing up Eargon Yeah, I'm not sure I follow either. Let's see if we have this right... On full disc, you get the error: No media inserted. Please insert a compatible media to start the write process. On main movie, the process seems to complete successfully, but the disc is blank?. Is this right? Are you still able to use the blank disc? is it really completely blank or just appear that way? Try main movie again, but do this first. "Common settings" > "General" > Unclick "Delete temporary files when finished" Remember the location of your temporary directory so you can find the files later on (just follow the file path). (You can actually place this directory anywhere you want on the hdd, just as you can choose any target location on the hdd instead of your burner, but do whatever is easy for you). Now, before you try to do another bkup, make sure your temp directory is empty...just delete anything in there. How much free space do you have on your hdd? Ok, try Main movie again. Let's assume your "bkup" is blank. Go to the temp directory...the files should still be there, even though the process completed successfully and you clicked on "Finished". You should be able to view the movie off your hdd. Let us know what happens... __________________ If it ain't broke, don't fix it! How to check DMA \| More DMA Help + Reset DMA link \| Nero CD-DVD Speed \| Regseeker \| VLC Media Player You know how to whistle, don't you, Steve? You just put your lips together and... blow. \| Lauren Bacall \| "To Have and Have Not" (1944).

28-03-2007	#14 (permalink)
Jimbo CD Freak Join Date: Oct 2006 Location: Arizona desert (SW) Posts: 2,451	Re: Trouble backing up Eargon Just a thought here, maybe your burner doesn't like TDK blank media, I know it might sound silly but my burners just don't like Sony disk, have problems with them and I thought Sony was a good brand, so I switched to Verbs' and no problems since __________________ Jim ( old desert rat ) Windows XP Home Edition SP3 112L FW 8.25 112L FW 8.25 Taiyo Yuden & Verbatim's only in my burners DVDFAB Platinum, DVD Next Copy

28-03-2007	#17 (permalink)
Bushwacker6566 New on Forum Join Date: Mar 2007 Posts: 17	Re: Trouble backing up Eargon I was able to copy it to my DVDFab folder as shown in pic below. Now I just need to figure out how to get it to disk and to view it on my pc lol. I too agree with those who were talking about disk's and my burner, only Ive backed up to these TDK disks already. So it kinda makes me wonder. I just tried to burn the files from my HDD as the source to a blank in the burner and got the No media inserted. Please insert a compatible media to start the write process.

28-03-2007	#19 (permalink)
bigmacnc CDFreaks Resident Join Date: Sep 2005 Posts: 1,728	Re: Trouble backing up Eargon Does the burned disc show the burn lines and what does windows explorer report that is on the disc? Mack __________________ Mack Find missing DVD or CD drives download CDGONE and Disable Auto Run Click Here Media Info: Click Here To understand DMA and how to lock it click Here The more problems that I have to deal with; the more I learn Clicking on Search or Searching on Google will not cause your computer to explode That is just a rumor

29-03-2007	#20 (permalink)
t0nee1 CD Freaks Die Hard Join Date: Nov 2006 Location: Wild Wild West Posts: 1,315	Re: Trouble backing up Eargon Bushwacker wrote "I was able to copy it to my DVDFab folder." if successful, then just use IMGBurn on VIDEO_TS folder to build an ISO....and burn... with diff. media.... preferably Verbs.....

29-03-2007	#24 (permalink)
Jimbo CD Freak Join Date: Oct 2006 Location: Arizona desert (SW) Posts: 2,451	Re: Trouble backing up Eargon Don't know whats going on here myself but the latest FW for that burner is 1.09 __________________ Jim ( old desert rat ) Windows XP Home Edition SP3 112L FW 8.25 112L FW 8.25 Taiyo Yuden & Verbatim's only in my burners DVDFAB Platinum, DVD Next Copy